(DIR) Return Create A Forum - Home
---------------------------------------------------------
Chainsaw Repair
(HTM) https://chainsawrepair.createaforum.com
---------------------------------------------------------
*****************************************************
(DIR) Return to: Stihl
*****************************************************
#Post#: 83547--------------------------------------------------
Re: Stihl info
By: jakeamondo Date: November 6, 2018, 9:47 am
---------------------------------------------------------
interesting info
(HTM) https://studylib.net/doc/18886534/technical-reference-guide
#Post#: 83549--------------------------------------------------
Re: Stihl info
By: Chainsawrepair Date: November 6, 2018, 10:26 am
---------------------------------------------------------
OK finally came up right. Look like spam at first. But loaded
right 3rd try.
3003 650 2539 30036502539 stihl 13T replacement bar tip
Stihl misc bolt nut kit 59100071061
#Post#: 83943--------------------------------------------------
Re: Stihl info
By: Chainsawrepair Date: December 30, 2018, 8:50 am
---------------------------------------------------------
You know I have been on a kick for buying tools to make my life
easier. Well one I never knew about but just bought because
there was times I wish I had something better. Bought a set of
stihl wrist pin punches. I know not needed, buttttttt. Just to
make my life alittle easier.
OEM Stihl piston pin assembly drifts
1106 893 4700
1107 893 4700
1108 893 4700
1110 893 4700
1111 893 4700
1114 893 4700
1130 893 4700
1135 893 4700
#Post#: 83947--------------------------------------------------
Re: Stihl info
By: jmester Date: December 30, 2018, 1:18 pm
---------------------------------------------------------
I have a few of them as well. They come in handy for sure. I
really like the tool for installing the earless piston pin clips
#Post#: 84682--------------------------------------------------
Re: Stihl info
By: Chainsawrepair Date: March 16, 2019, 1:41 pm
---------------------------------------------------------
conical washer 9331 630 0120
#Post#: 84694--------------------------------------------------
Re: Stihl info
By: Chainsawrepair Date: March 19, 2019, 1:25 pm
---------------------------------------------------------
Redbull =
first gen solenoid = Black - pn# 0000 120 5110 - should use with
black fuel filter
current gen solenoid = White - pn# 0000 120 5104 - should use
with orange fuel filter
new exploratory solenoid that apparently has now been scrapped =
Green - pn# 0000 120 5111
orange fuel filter, white solenoid and new coils have 2yr
warranty. After that it sounds like stihl will replace parts but
you will have to pay labor.
If you have problem on the -
MS241 - he didn't have any info on the 241 yet.
MS261 cm - replace black solenoid to white solenoid and black
fuel filter to orange fuel filter. (they are coming out with a
kit for this (contains white solenoid and orange fuel filter)
Use "RESET" (90sec choke, 60 sec idle, 5 cuts). There are no
gen3 control modules/coils thus you don't use "Calibration"
(30-40sec choke, 20-30sec WOT, let off after it goes from max to
scream back to max :D)
MS362 cm - same as 261 above.
MS462 cm - all 462s have gen3 control modules/coils, white
solenoids, and orange fuel filters. So obviously stick to doing
"Calibration" and replacing white solenoid and orange fuel
filter with a white solenoid and orange fuel filter.
MS661 cm - little more complicated on the 661...
If control module/coil = 4700c 4700d 4700e(gen1) 4701a(gen2) -
then must stick with black solenoid, black fuel filter, and
doing the "RESET" (90 sec choke, 60sec idle, 5 cuts). You should
not inter change any of the parts ...apparently problems with
doing so. For example a white solenoid with 4701a coil and black
fuel filter.
If control module/coil = 4702 4703 4704(gen3) - then must stick
with white solenoid and orange fuel filter. And of course you do
a "Calibration" not a "RESET".
There is a kit specifically for the 661 which includes the ver3
coil, white solenoid, and orange fuel filter 1144 007 1801
#Post#: 85269--------------------------------------------------
Re: Stihl info
By: Chainsawrepair Date: June 22, 2019, 9:14 am
---------------------------------------------------------
Saving info someone may need someday.
#Post#: 85318--------------------------------------------------
Re: Stihl info
By: joe_indi Date: July 1, 2019, 8:50 am
---------------------------------------------------------
I do have the Electronic Catalogue from the 90s. And it has the
Testing and Setting Data in pdf for older saws and other
machines. I can screen grab the pages (painful process) or pm
the file to you (easy ;D)
Sample page below
#Post#: 85319--------------------------------------------------
Re: Stihl info
By: joe_indi Date: July 1, 2019, 8:54 am
---------------------------------------------------------
another grab
#Post#: 85320--------------------------------------------------
Re: Stihl info
By: Chainsawrepair Date: July 1, 2019, 9:50 am
---------------------------------------------------------
[member=130]joe_indi[/member] make sure is different then this
link before you go through the trouble.
(HTM) http://slugaservice-com.3dcartstores.com/assets/html/S_specs.html
*****************************************************
(DIR) Previous Page
(DIR) Next Page